
Egress Window Installation in Des Moines: Cut, Frame, Flash and Drain It Right the First Time
Des Moines sits on the dense glacial till clay of the Des Moines Lobe, where the Des Moines and Raccoon rivers meet, and that geography decides how an egress window has to be built. Whether you are in a 1920s brick bungalow in Beaverdale with a block wall basement, a foursquare in Waterbury, or a 2010s Colonial in West Des Moines with a poured-concrete basement, an Egress Window Installation in Des Moines is a cut through the foundation wall first and a drainage job second. We cut, frame, flash and drain the opening so the new bedroom or living space below grade stays dry through spring snowmelt and summer thunderstorms. If you are planning a basement finish, this work pairs naturally with basement waterproofing before the drywall goes up. We are a Basement Health Association (BHA) member and we work below grade only.
Why an Egress Window Cut Matters More in Des Moines Than in Most Markets
The Des Moines metro has a huge stock of full basements: clay-tile and block walls in Sherman Hill, Drake, Beaverdale and Windsor Heights, and poured concrete in Ankeny, Waukee, Grimes and the newer West Des Moines subdivisions. Every one of those walls holds back wet glacial clay and a high water table in the river bottoms that flooded in 1993 and 2008. Cut a hole in that wall without flashing and drainage and you have built a funnel into the room.
- We cut the opening to the rough-in size the window manufacturer specifies, not to whatever the saw happens to reach.
- We frame the opening with treated lumber and anchor it to the existing wall so the header carries the load above.
- We flash the sill and jambs and tie the flashing into the wall so water sheds to the outside, not into the block cores.
- We install a drained window well with gravel and a connection to daylight or to the footing drain, because a well that holds water is a wet basement waiting to happen.
- We seal the interior perimeter and check the wall for existing seepage, efflorescence and hairline cracks before we close anything up.
On a 1940s bungalow in Beaverdale, the cut often exposes an old clay-tile wall that needs repointing before the window goes in. We tell you that before the saw comes out.
Key info: In Johnston and Urbandale, 1970s split-levels frequently have a finished basement already, and the homeowner wants a second egress point for a bedroom. We cut from the inside out, protect the finished floor, and stage the debris so the room stays usable the same week. Egress window cutting is a structural alteration, so permits are commonly required and rules vary by jurisdiction. Always verify with the local building department before work starts.
For the code side of the opening size and sill height, the City of Des Moines permits and inspections office is the authority to check: City of Des Moines Permits and Inspections.
How We Cut, Frame and Drain an Egress Window in a Des Moines Basement
We do this in a fixed sequence because each step protects the next. On a poured-concrete Colonial in Ankeny the wall is dense and the cut is clean; on a 1910s brick foundation in Sherman Hill the mortar is soft and the cut has to be slower and shored as we go. The sequence is the same either way.
- We walk the basement, mark utilities, and confirm the opening location against the window well and the grading outside.
- We cut the wall with a wet saw or core drill, in sections, and shore the opening as we cut.
- We frame the rough opening with treated lumber, set the header, and anchor the frame to the existing wall.
- We flash the sill and jambs, install the window, and seal the interior and exterior perimeters.
- We set the window well, add gravel, and connect the well drain to daylight or to the footing drain so it does not pond.
- We regrade and extend the downspout so roof water moves away from the new opening.
If the wall shows active seepage during the cut, we stop and address it before the window goes in. The right fix is often an interior drain tile system tied to a sump basin, not a smear of hydraulic cement over a wet block wall.
Key info: A West Des Moines homeowner in a 2005 Colonial wanted a legal bedroom in a finished basement. The cut went through a poured wall with no crack, but the window well sat on the low side of the lot and filled with snowmelt every March. We set a drained well with gravel and a dedicated line to daylight, and the room stayed dry through the next spring. That well detail is where most egress jobs fail.
Egress Window Installation Methods We Use on Des Moines Foundations
The right method depends on the wall material and on how the water table behaves at your address. A block wall in Windsor Heights and a poured wall in Grimes are not the same cut, and the well drainage is not the same either.
| Approach | Description | Best for |
|---|---|---|
| Wet-saw cut with framed opening | Precision cut of the foundation wall, treated frame, header, and full flashing and sealing at the perimeter. | Poured-concrete basements in Ankeny, Waukee and newer West Des Moines builds. |
| Block or brick wall cut with repointing | Slower cut through block or brick, repointing of disturbed mortar, and a sealed frame tied into the wall. | 1920s to 1950s bungalows and foursquares in Beaverdale, Drake and Waterbury. |
| Drained window well with gravel and daylight line | Well set on gravel with a drain connected to daylight or the footing drain so the well does not pond. | Low-side lots and river-bottom properties near the Des Moines and Raccoon rivers. |
| Waterproofing before the finish | Crack repair, wall sealing and drainage addressed before the new room is framed and drywalled. | Any basement finish where the wall shows seepage or efflorescence. |
| Structural review before the cut | Assessment of bowing, step cracking or prior repairs before an opening is cut into the wall. | Older stone and brick foundations with visible movement. |
We match the method to the wall in front of us, and we tell you when a simple sealed frame is enough and when the wall needs repair first.
Egress Window Installation Cost in Des Moines: What to Expect
Most egress window jobs in the Des Moines metro start at $4,500, and that figure covers a standard cut, frame, window, flashing and a drained well on an accessible wall. The number moves from there based on wall material, depth of cut, well height, and whether the basement needs waterproofing before the finish. A block wall in Windsor Heights takes longer than a poured wall in Ankeny, and a deep well on a river-bottom lot in Pleasant Hill adds drainage work.
- Wall material drives labor: poured concrete cuts fast, brick and block take longer and may need repointing.
- Well depth and drainage drive material cost, especially where the lot grades back toward the house.
- Interior access matters: a finished basement needs floor protection and careful debris staging.
- Existing seepage or cracks must be repaired before the window goes in, and that is a separate line item.
- Permit fees vary by jurisdiction and are commonly required for egress window cutting.
Get two or three written estimates on the same scope so you are comparing the same cut, the same window and the same drainage detail. Our full pricing overview lays out the ranges before you call.
Egress Window Installation Near Me: How to Vet a Contractor Near Des Moines
Egress work is a structural cut plus a drainage detail, and not every contractor who advertises basement work does both well. Ask the same questions we would ask if we were hiring. A general foundation firm may cut the wall and leave the well drainage to someone else, and a plumber is not the right call for a foundation opening.
- Confirm the contractor is licensed and insured for structural work in Iowa, and ask for a certificate of insurance.
- Get at least two or three written estimates on identical scope, and read what is excluded.
- Ask for references from jobs in Des Moines, Urbandale or Ankeny with the same wall type as yours.
- Confirm who pulls the permit and who handles inspection with the local building department.
- Ask how the window well drains and where that water goes, in writing.
If a contractor cannot explain the well drainage and the flashing detail in plain terms, keep calling. You can reach us through our contact page and we will walk the basement with you before any number is given. We also serve the surrounding metro, including West Des Moines (50265) and Ankeny (50023), with the same cut, frame and drain sequence.
Egress Window Installation in Des Moines: Pricing Guide
| Service | Price | Details |
|---|---|---|
| Standard egress window cut and install | Starting at $4,500 | Includes wall cut, treated frame, header, window, flashing and perimeter sealing on an accessible wall. |
| Block or brick foundation cut | Starting at $5,200 | Slower cut through block or brick with repointing of disturbed mortar and a sealed frame tied into the wall. |
| Drained window well with daylight line | Starting at $1,800 | Well set on gravel with a drain connected to daylight or the footing drain so the well does not pond. |
| Waterproofing before the finish | On estimate | Crack repair, wall sealing and drainage addressed before the new room is framed and drywalled. |
| Travel | Included | In Des Moines and the surrounding metro, with no separate call-out or mileage fee. |
| Estimate | Free | Response within 24 hours at (515) 834-4110, with no obligation to book the work. |
Indicative pricing, the exact cost depends on square footage, finish, and site access. Free personalized estimate within 24h at (515) 834-4110.